Due to the clicking (is that click of death? is that even a jaz drive thing, as I thought that was a zip drive thing?!?) and the refusal to see the disk as writable means something is wrong with the drive. Among my many attempts, I even tried it without the disk inserted and it would recognize the drive. I tried other disks, I tried removing the CD driver (extension), thinking maybe it was interfering with the iomega driver. I know for a fact it is not write protected, as I had used the disk in my 2g external jaz drive successfully. When I tried to initialize it, it would mess about for a bit and then come back with the CD icon and tell me the disk was write protected. It did a lot of clicking, eventually it would say the disk needed initialized. My Mac SE/30 properly recognized the drive and its SCSI ID (6) and even recognized that there was a disk inserted! SCSIprobe didn't report any SCSI termination issues and my other SCSI devices were working fine (I had a zip drive connected on ID 5, and no, it was not terminating the chain, the terminator switch was off on the zip drive).īut that's where the good news stopped. Tested the one internal 1g jaz drive as an external setup with an ATX power supply and a ribbon-to-din adapter. At least my 2G jaz drive works! But there go my dreams of installing an internal jaz drive in both my PC and Mac SE/30!. The 2G jaz drive sounds fine - like an old hard drive. I'm going to try pulling it out and swapping it with the clicking one. One just spins and clicks - is that the click of death? The other takes the disk, spins it up, then just sits there - that's the one I have connected to the Win10 PC. I have two internal Jazz 1G drives, and I don't think either works properly. I backed the data up, then formatted the disks. It opened all of the disks and they even had data on them from the previous owner. Now that I've got a working SCSI card in the Win10 PC, it recognized the 2GB external jaz drive without any issue. I don't know why I didn't think of it, but I tried the same jaz disks in a known good working 2gb external drive. I think I might have a pair of bad drives. I use your System 7 image files all the time. If the above steps do not resolve the issue, consult a professional for further assistance.Click to expand.I very much appreciate the info, RS! And even more, I _really_ appreciate your site! I've learned a lot of things from your pages. There are various reputable data recovery tools available online that can help recover data from faulty drives. Test with a different cable or enclosure: If you have access to another compatible USB cable or an external hard drive enclosure, try connecting the iOmega hard drive using those to rule out any cable or enclosure issues.ĭata recovery software: If none of the above steps work and you have valuable data on the iOmega hard drive, consider using data recovery software to retrieve your files. If it does, but is not assigned a drive letter, right-click on the drive and select "Change Drive Letter and Paths." Assign an available drive letter to the external hard drive. If it is recognized on another computer, the problem may be related to your Windows installation or USB drivers.ĭisk Management: Open Disk Management by right-clicking on the Start button and selecting "Disk Management." Check if the iOmega hard drive appears in the list. Repeat this for all USB Root Hub entries.ĭrive recognition: If the external hard drive is not recognized at all, you can try connecting it to a different computer to determine if the issue lies with the drive or your computer. Right-click on each USB Root Hub entry and select "Update Driver" to check for any available updates. USB driver update: In Device Manager, expand the "Universal Serial Bus controllers" section. If you find any, right-click on the device and select "Update Driver" to search for the latest driver software. Look for any yellow exclamation marks or question marks next to the iOmega hard drive entry. This can help reset the device.ĭevice Manager check: Open Device Manager by right-clicking on the Start button and selecting "Device Manager" from the menu. Wait for a few seconds, then reconnect the power and USB cables. Power cycle the hard drive: Disconnect the power source from the iOmega hard drive (if it has a separate power adapter) and also unplug the USB cable. If possible, try using a different USB port to rule out any port-related issues. Troubleshooting external Iomega hard drives on Windows 11 and 10 can be done by following these steps:Ĭheck the physical connections: Ensure that the USB cable connecting the external hard drive to your computer is securely plugged in on both ends.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |